IoT / EMBEDDED / CONNECTED DEVICES

From development boards to connected systems.

A working catalogue of embedded skills, boards and modules explored, and devices and infrastructure built around them. The focus is the complete path: firmware, hardware interfaces, connectivity, deployment and observability.

Boards & modulesMy hardware inventorySensors & Peripherals ↓Things built

Skills & engineering areas

01 / Firmware

Embedded development

Firmware architecture, hardware bring-up, peripheral integration and real-time device behavior.

ESP-IDFESP-ADFFreeRTOSC/C++GPIOI²CSPII²S
02 / Connectivity

Device networking

Connecting embedded endpoints to services, communication systems and low-bandwidth networks.

Wi-FiSIP/RTPMQTTLoRaReticulumTCP/IP
03 / Lifecycle

OTA & fleet operations

Firmware artifacts, device status, provisioning, rollout safety, remote diagnostics and monitoring.

OTAProvisioningTelemetryPrometheusGrafana
04 / Integration

Hardware & interfaces

Audio pipelines, displays, controls, radios and the interfaces that connect components into a product.

Audio codecsE-paperRotary controlsUARTADCPower management

Development boards & modules

This is a growing workbench catalogue, not a claim that every listed board is currently in inventory. Entries distinguish platforms used in projects from modules explored during prototyping.

MCU / Wireless

ESP32 family

ESP32-S3 firmware work, audio and peripheral integration, wireless experiments and device control.

ESP32-S3ESP-IDFWi-FiBLE
Audio / Product prototyping

Waveshare audio development hardware

Audio-capable development hardware used as a starting point for embedded voice and interface experiments.

I²S audioMicrophoneSpeakerFirmware
Radio / Long range

LoRa modules & boards

Low-bandwidth radio experiments and resilient device-to-device networking concepts.

LoRaReticulumRF
Cellular / Telephony

SIM800L GSM module

Exploring cellular connectivity and the role of a GSM module in PBX and voice gateway designs.

GSMUARTAT commandsPBX integration
Display / Interface

E-paper and physical controls

Low-power display integration, buttons, rotary input and compact device interaction patterns.

E-paperSPIGPIOLow power

My Devices & Hardware Inventory

This catalogue consolidates hardware mentioned across my project notes and board-identification conversations. Models are listed as specifically as the records allow; uncertain markings and overlapping camera/display variants are called out rather than silently treated as separate purchases.

Custom product hardware

LOUP custom PCBs — 2 boards

Two custom LOUP boards for the ESP32-S3 child-safe voice-device project, integrating audio, e-paper, physical controls, Wi-Fi and SIP/RTP firmware.

2 PCBsESP32-S3ES8311ES7210E-paperSIP/RTP
Custom product hardware

LOUP phone prototype — 1 device

One working LOUP voice-device prototype, counted separately from the two custom PCBs.

1 prototypeVoice deviceOTA
Custom development hardware

Qings Custom Board

Custom board referenced in the hardware inventory. The exact MCU, revision and interfaces still need confirmation from its silkscreen or design files.

Custom PCBBoard bring-up
ESP32 / confirmed board list

Seeed Studio XIAO ESP32-S3

Compact ESP32-S3 development board; the China purchase was specifically confirmed in the notes.

ESP32-S3Wi-FiBLEChina purchase noted
ESP32 / confirmed board list

ESP32-S3 N16R8

ESP32-S3 board recorded with 16 MB flash and 8 MB PSRAM designation.

ESP32-S316 MB flash8 MB PSRAM
ESP32 / marking needs confirmation

ESP32-S3 “1116P8” board

A board was recorded under the marking “ESP32-S3 1116P8”. This label is retained verbatim until the module marking is checked against a clear photo.

ESP32-S3Exact variant unverified
ESP32 / compact board

ESP32-S3 SuperMini

Compact ESP32-S3 development board for small embedded experiments and peripheral tests.

ESP32-S3Compact form factor
ESP32 / camera

ESP32-CAM

Camera-capable ESP32 development hardware for image capture and edge-vision experiments. This generic inventory entry may overlap with the more specific camera board below.

CameraOV2640 familyWi-Fi
ESP32 / camera variant

GOOUUU ESP32-S3-CAM V1.5 — OV2640

Specifically named camera board from the project notes. Kept distinct for identification, but not assumed to be an additional unit beyond the camera hardware already counted until reconciled with photos.

ESP32-S3OV2640V1.5Vision experiments
ESP32 / general-purpose

Generic ESP32 development boards — 2

Two generic ESP32 boards were explicitly recorded as held. They have also been discussed for controlling or interfacing with external radio modules.

2 boardsGPIOUARTSPI
Waveshare / audio

Waveshare Audio Development Board

Audio development hardware used in embedded voice and codec experiments. The LOUP design uses ES8311 playback and ES7210 microphone capture paths; exact board revision should be checked against the device.

I²SAudio codecMicrophoneSpeaker
Waveshare / wearable interface

Waveshare Smartwatch Board

Wearable-form-factor development board recorded in the held inventory, for compact UI and embedded interaction experiments.

DisplayWearableEmbedded UI
Waveshare / high-performance MCU

Waveshare ESP32-P4-Pico

ESP32-P4 development board for higher-performance UI, camera/display and peripheral work. The P4 itself does not provide native Wi-Fi/Bluetooth, so wireless functionality depends on additional hardware.

ESP32-P4Display interfacesUSB OTG
Waveshare / LCD

Waveshare ESP32-C6-LCD-1.47

Small LCD-equipped ESP32-C6 board referenced in the inventory notes. Its inclusion in the stated count of 12 needs reconciliation.

ESP32-C61.47-inch LCDWireless
Waveshare / sub-GHz & multi-band radio

Waveshare ESP32-S3-LR1121-LF

ESP32-S3 board with LR1121 radio hardware for long-range and multi-band wireless experiments.

LR1121ESP32-S3LoRaSub-GHz
Heltec / LoRa display

Heltec WiFi LoRa 32 V4.3 — HTIT-WB32LAF V4.3

Board identification was corrected from an earlier V3.2 guess after inspecting the PCB marking. The recorded V4.3 identification is the one to use.

ESP32-S3SX1262LoRaDisplayV4.3
EBYTE / LoRa radio module

EBYTE E22-400T22D V2

400 MHz-band LoRa UART radio module recorded in the user's radio hardware notes.

400 MHz bandUARTLoRa
EBYTE / radio module

EBYTE EWM22A-400R30D

400 MHz-band radio module specifically listed in the hardware notes; exact integration and antenna configuration depend on the module datasheet.

400 MHz bandRFRadio module
Cellular / GSM

SIM800L GSM module

Cellular modem module for GSM connectivity experiments and research into a possible GSM-to-SIP/PBX gateway. The module is not presented as a completed bidirectional gateway.

GSMUARTAT commandsPBX research
Additional board reference

ESP32-C3 / ESP32-C6 modules and boards

ESP32-C3/C6 hardware appeared in earlier board-photo and inventory discussions. Exact models and whether these are separate units from the named C6 LCD board remain unconfirmed.

ESP32-C3ESP32-C6Variant check pending

Count reconciliation: the notes say 12 development boards, plus 2 LOUP PCBs and 1 LOUP prototype. The named list above includes additional explicitly referenced variants/modules, so it must not be read as a verified count of 12 unique boards. Camera variants and the ESP32-C6-LCD entry may overlap with the original count. Raspberry Pi and Arduino Uno appeared in earlier photo context, but are not counted as confirmed owned/purchased items without a matching inventory record.

Sensors & Peripherals

Sensors & Peripherals — inventory and interface map. Confirmed hardware, unidentified parts, and design/research candidates are labelled separately. Use the jump link near the top of this page to return here quickly.

Sensor inventory & sensing capabilities

A sensor appearing in the research list does not mean it has been purchased or is currently in the parts box.

Owned / model not identified

3-pin sensor module with black bead

A small black, three-pin module with a bead-shaped component was shown in an earlier hardware-identification conversation. It may be a thermistor or temperature-sensing module, but its exact part number and function remain unconfirmed.

3-pin modulePossible thermistorPhoto identification needed
Camera hardware / model partly identified

OV2640 camera module

The GOOUUU ESP32-S3-CAM V1.5 is recorded with an OV2640 camera. The sensor attached to the separate Classic ESP32-CAM still needs visual confirmation; do not assume both camera boards use the same sensor.

OV2640Image captureESP32-S3-CAM
On-board sensing / details unknown

Waveshare Smartwatch Board sensors

The smartwatch board is in the owned hardware inventory and was previously noted as having sensors, but the exact on-board sensor ICs have not been identified from a verified board revision or schematic.

On-board sensorsExact ICs unverified
Audio input / owned development hardware

Microphone and audio capture path

The Waveshare Audio Development Board and LOUP audio hardware support microphone/audio-input work. LOUP's recorded audio path uses an ES7210 microphone ADC and ES8311 playback codec; these are audio-interface components, not environmental sensors.

Microphone inputES7210I²SAudio sensing
Discussed / ownership not confirmed

HC-SR04 ultrasonic distance sensor

An HC-SR04 ultrasonic sensor was discussed for an ESP32 experiment. Past context does not conclusively confirm that this module is owned.

UltrasonicDistanceESP32 experiment
Research / not confirmed in inventory

Environmental sensors

BME280 and general temperature, humidity and pressure sensing were discussed as possible embedded capabilities. No specific owned BME280 module has been confirmed in the available notes.

BME280 discussedTemperatureHumidityPressure
Research / not confirmed in inventory

Time-of-flight and gesture sensors

ST VL53L5CX ToF, PAJ7620U2 gesture IC and APDS-9960 gesture/proximity sensing were considered in earlier design discussions. They are not counted as owned parts.

VL53L5CXPAJ7620U2APDS-9960Proximity / gesture
Research / not confirmed in inventory

Motion, inertial and presence sensing

Accelerometer/gyroscope and IMU sensing, PIR presence detection and radar-based presence sensing have appeared in project planning. Exact modules and ownership are unverified.

AccelerometerGyroscope / IMUPIRRadar
Research / not confirmed in inventory

Load, electrical and device-state sensing

Load cells with HX711, current/voltage measurement, ADC-based inputs and a MAX17048 battery fuel gauge were discussed for potential device designs. These are not represented as confirmed owned modules.

Load cell / HX711Current / voltageADCMAX17048 discussed
Research / not confirmed in inventory

Positioning and GNSS

GPS/GNSS was mentioned in broader device architecture discussions, but no specific owned GPS receiver or GNSS module has been verified in the available inventory notes.

GPSGNSSModule unconfirmed
Research / not confirmed in inventory

Microphone arrays and advanced gas sensing

PDM MEMS microphones, microphone arrays and a Seeed reSpeaker Flex XVF3800 Linear-4 were discussed as options. Electrochemical and NDIR gas sensors were also mentioned in earlier system planning; none are confirmed as owned inventory here.

PDM MEMSXVF3800 discussedElectrochemicalNDIR
Project concepts / not owned-confirmed

Appliance and kiosk sensors

Cup detection, water-level, coffee-level, leak and door sensors were discussed for a coffee-kiosk concept. These are requirements from that concept, not a claim that those parts are on hand.

Cup detectionWater levelLeakDoorTemperature
Design discussion / ownership unconfirmed

Light and optical sensing

Ambient-light and optical proximity sensing were relevant to compact UI and device-interaction discussions. No specific LDR, photodiode or light-sensor module is confirmed in the current owned inventory.

Ambient lightOptical sensingPart unverified
Design discussion / ownership unconfirmed

Temperature sensing and thermistor input

The unidentified three-pin black-bead module may be a thermistor-style temperature sensor, but this must be checked from a photo or part marking before naming it conclusively. Temperature sensing also appeared in kiosk requirements.

Thermistor candidateTemperatureADC / GPIO
Project concept / not confirmed owned

Water, liquid and leak detection

Water-level and leak-detection inputs were discussed for a kiosk/appliance concept. No specific float switch, capacitive level probe or leak-sensor board is verified as owned.

Water levelLeak detectionInterface planning
Research / not confirmed owned

Gas, smoke and air-quality sensing

Gas-sensing ideas included electrochemical and NDIR approaches. These remain research candidates; no specific MQ-series, CO₂ or air-quality sensor is confirmed in the inventory.

Gas sensingCO₂ / NDIRElectrochemicalNot inventory-confirmed
Research / not confirmed owned

Rotational, touch and user-input sensing

Rotary input and physical buttons are part of the LOUP/custom-device interface work. Dedicated capacitive-touch modules or separate encoder modules have not been confirmed as standalone purchases.

Rotary inputButtonsCapacitive touch discussed
Research / not confirmed owned

Flow, weight and force sensing

Load-cell/HX711 interfaces and flow/level sensing were considered for measurement and kiosk concepts. They are shown as possible integration areas, not confirmed physical inventory.

Load cell / HX711FlowForce / weight

Peripherals & hardware interfaces

These components and interfaces have appeared in the LOUP, wearable, audio and low-power device design notes. Items marked discussed are architecture references, not proof of a separate purchased module.

Display / discussed in project notes

Sharp 400 × 240 Memory LCD

A low-power reflective display option discussed for compact embedded UI. It is separate from the LOUP e-paper display and is not counted as confirmed owned hardware.

Memory LCD400 × 240Low power
Audio / discussed interface

MAX98357A I²S amplifier and speaker

The MAX98357A digital I²S amplifier and speaker appeared in earlier audio-device planning. The LOUP design also uses ES8311/ES7210 audio paths; these are distinct implementation references.

MAX98357A discussedI²SSpeaker output
Power management / discussed

BQ25185 power-management IC

Battery charging and power-path management component referenced in portable-device design notes. Exact implementation and board ownership are not confirmed here.

BQ25185Battery chargingPower path
Battery telemetry / discussed

MAX17048 fuel gauge

Battery-state-of-charge monitoring was discussed for compact battery-powered devices. This is a design reference rather than a verified standalone module in the inventory.

MAX17048Battery telemetryI²C
Timekeeping / discussed

RV-3028 real-time clock

A low-power RTC appeared in prior device design notes for maintaining time across sleep or power loss. A separately owned RTC board has not been confirmed.

RV-3028RTCI²C
Physical interface / project context

Rotary encoder and buttons

Physical controls are part of the LOUP interface, including rotary input and buttons. Current custom-board notes use ADC-based controls; this describes the interface function rather than assuming a separate encoder module.

Rotary inputButtonsGPIO / ADC
Connectivity / interface capability

USB-C, UART, I²C, SPI and I²S

Wired bring-up and peripheral integration across the named boards: USB-C for power/data where supported, UART for radio/modem modules, I²C for control/sensors, SPI for displays/radios, and I²S for digital audio.

USB-CUARTI²CSPII²S
Wireless peripheral capability

Wi-Fi and Bluetooth LE

Wireless interfaces used or considered across ESP32-family boards for provisioning, telemetry, local control and device networking. Availability depends on the exact MCU and board; ESP32-P4 requires external wireless hardware.

Wi-FiBLEProvisioningTelemetry
Custom hardware / confirmed project context

Custom PCB, power rails and expansion I/O

LOUP custom boards integrate MCU, audio, display, physical controls and peripheral buses. Exact exposed interfaces vary by board revision; this describes integration work, not that every interface is exposed on every board.

Custom PCBPower railsGPIOPeripheral integration

Inventory accuracy: confirmed from context are the photographed unidentified 3-pin black-bead module, camera-capable boards (with OV2640 specifically recorded for the GOOUUU ESP32-S3-CAM), the smartwatch board with unidentified on-board sensors, and microphone/audio-input hardware. Other sensor models are included for traceability but explicitly marked as discussed or unverified—not as confirmed purchases.

Things built, tested & in progress

Project status is stated explicitly: built/tested work is separated from research and planned experiments.

Built / working prototype

LOUP connected voice device

Child-safe Wi-Fi voice communication device built around custom ESP32-S3 hardware, ES8311/ES7210 audio, e-paper UI, physical controls, SIP/RTP calling and managed firmware updates. China prototype and EVT/PVT work have been reported.

ESP32-S3AudioSIP/RTPOTACustom PCB
Built / embedded learning device

Pocket Dinosaur Explorer

ESP32/OLED interactive learning-device project with letters, numbers, animals and stars, plus a web control interface.

ESP32OLEDWeb controlLearning UI
Built / firmware backup exists

Glowtank

ESP32 project with a preserved pre-OTA firmware image. Listed as an existing project; detailed feature claims are intentionally omitted until its current firmware and hardware are inspected.

ESP32FirmwareOTA workflow
Built / operations tooling

OTA fleet control plane

Firmware artifact handling, compatibility checks, rollout state and operational visibility for connected devices.

Firmware deliveryFleet statusOperations
Research / prototype work

Wi-Fi CSI presence sensing

Signal collection, calibration, feature extraction and visualization using Wi-Fi channel-state information.

ESP32-S3CSISignal processing
Research / radio networking

LoRa, EBYTE and Reticulum experiments

Radio-module identification and integration planning around Heltec, LR1121 and EBYTE hardware, including resilient low-bandwidth networking concepts. Do not imply every module is already operating as a deployed network.

LoRaLR1121E22-400Reticulum/RNode
In progress / research

ESP32 camera and AI vision

Camera-board firmware and a hybrid, free-tier vision plan for person detection and tracking using local webcam capture with Hugging Face/Colab experiments. This is a development target, not a claim of completed edge-AI deployment.

ESP32 cameraPerson detectionTrackingOpen source
Research / integration not yet complete

SIM800L-to-SIP/PBX gateway investigation

Investigating how to bridge cellular GSM calls into an Asterisk/SIP environment using the available SIM800L and ESP32 audio hardware. A ready-made complete bidirectional firmware solution has not been verified.

SIM800LAsteriskSIP/RTPUART/audio bridge
Related work

Systems & capabilities

See the wider engineering stack across embedded firmware, communications, Linux infrastructure and observability.

This page will evolve as boards, modules, experiments and completed builds are documented. Prototype, in-progress and production work should remain clearly labelled rather than presented as equivalent milestones.