ROS 2 and Microcontroller Firmware: Where Each Layer Belongs
ROS 2 and Microcontroller Firmware: Where Each Layer Belongs. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
ROS 2 and Microcontroller Firmware: Where Each Layer Belongs. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Why CAN Bus Is Useful in Robots with Multiple Motor Controllers. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Why Robot IMUs Drift—and How Sensor Fusion Helps. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Robot Sensor Calibration: Why Raw Numbers Are Not Yet Measurements. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Building a Line-Following Robot That Works Beyond the Demo. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Microcontroller or Raspberry Pi-Class Computer: Which Belongs in a Robot?. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Emergency Stops and Safe Motor Shutdown in DIY Robotics. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Ultrasonic vs Time-of-Flight Sensors for Robot Obstacle Avoidance. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Why Robot Firmware Needs State Machines Instead of a Giant Loop. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
How Quadrature Encoders Help a Robot Measure Wheel Speed and Distance. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Arduino, ESP32, and STM32 are not perfectly equivalent choices: one is an ecosystem, one is a chip family, and one is a broad microcontroller portfolio. Choose by project constraints, not popularity alone.
Debugging Robot Motor Oscillation: Start with Measurements, Not New PID Values. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Watchdogs and Fail-Safe Behavior in Autonomous Robot Firmware. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
PWM Motor Control Explained: What a Microcontroller Actually Changes. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Interrupts let a processor respond to events without continuously polling every input. Their power comes with constraints: short handlers, shared-state discipline, latency, and careful event design.
What It Takes to Build a Self-Balancing Robot with a Microcontroller. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
A microcontroller does not simply wake up and run your application. Reset logic, boot memory, startup code, clocks, and memory initialization prepare the chip before your first line of application code executes.
Testing Robot Firmware with Hardware-in-the-Loop Techniques. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
A GPIO pin can fail for reasons that have little to do with the line of code that configures it. Pin multiplexing, electrical levels, reset behavior, boot straps, and board design all deserve a systematic check.
From Servo Pulses to Robot-Arm Motion: Understanding the Control Layers. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
In embedded C, volatile tells the compiler that an object's value may change outside the visible program flow. It is important for hardware registers and certain shared variables, but it is not a universal concurrency fix.
PID Control for Microcontroller Robots: From Oscillation to Stable Motion. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Designing a Robot Power System: Motors, Regulators, Batteries, and Brownouts. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
Choosing a Motor Driver for a Microcontroller Robot. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.
How to Choose a Microcontroller for Your First Serious Robot. Practical guidance on design trade-offs, common failure modes, and how to validate a real embedded robotics project.